NACE-CIP1-001 Tested & Approved CIP Level 1 Study Materials
Validate your Skills with Updated CIP Level 1 Exam Questions & Answers and Test Engine
NEW QUESTION # 38
If inspectors identify issues of non-conformance during an inspection, they should
- A. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. perform additional tests secretly to ensure there are no other potential issues at the site
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: A
NEW QUESTION # 39
Polymerization is the process of:
- A. Monomers joining together
- B. All organic coatings
- C. All thermoplastic coatings
- D. Monomers telegraphing
Answer: A
NEW QUESTION # 40
ISO ST 3 is described as:
- A. Thorough blast cleaning
- B. Thorough hand tool cleaning
- C. Very Thorough hand or power tool cleaning
- D. Very Thorough power tool cleaning
Answer: C
NEW QUESTION # 41
Checking is
- A. a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.
- B. surface breaks in the film that often result from grease or oil contamination and revel the substrate.
- C. an exposed area of the substrate or previous coat material, caused by poor application technique.
- D. a fine crack in the surface of a coating that rarely reaches the substrate
Answer: D
NEW QUESTION # 42
Owners hire NACE Inspectors' with the expectation that:
- A. The inspection cost will be offset by an improvement in service life
- B. The Inspector will make a meaningful technical contribution to the job
- C. a) and c)
- D. The Inspector will improve job flow and schedule
Answer: C
NEW QUESTION # 43
ASTM Standards are applicable:
- A. When specified
- B. In Asia
- C. In North America
- D. In the USA
Answer: A
NEW QUESTION # 44
You are the NACE Coating Inspector on an exterior job where the contractor is not using any environmental controls, For the last several hours your reading; indicate the relative humidity is rising and the substrate temperature is dropping. The sky is clouding over and the weather forecast is for evening showers. It is now 4 PM, your readings indicate you have minimally acceptable environmental conditions, however if the current trend continues, you expect to be outside specified conditions soon. The contractor advises you he is going to mix up the next full kit to complete his for the day.
Your FIRST preformed course of action is to:
- A. Advise the Contractor he cannot proceed
- B. Advise the Contractor of your readings
- C. Call your supervisor
- D. Advise the Contractor he can proceed
Answer: B
NEW QUESTION # 45
Most industrial coatings are:
- A. Inorganic
- B. Resistant to temperatures above 200C
- C. Organic
- D. Resistant to concentrated sulfuric acid
Answer: C
NEW QUESTION # 46
The form of corrosion that has the largest potential for unexpected catastrophic failure is:
- A. Galvanic Corrosion
- B. Atmospheric Corrosion
- C. General Corrosion
- D. Localized Corrosion
Answer: A
NEW QUESTION # 47
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Default to the owner's Inspection and Test Plan
- B. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- C. Bring the matter up at the pre-job conference
- D. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
Answer: C
NEW QUESTION # 48
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Presence of weld spatter may produce a false positive
- B. Synthetic oil or grease may not be identified
- C. Ultra-Violet light may contaminant the surface
- D. Chloride salt may produce a false positive
Answer: B
NEW QUESTION # 49
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Abrasive blast nozzles
- B. Power tools
- C. Airless spray equipment
- D. Hand tools
Answer: B
NEW QUESTION # 50
Dew point is the temperature at which
- A. humidity decreases
- B. the air is saturated.
- C. water freezes.
- D. condensation occurs.
Answer: D
NEW QUESTION # 51
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:
- A. Go with the majority opinion
- B. Achieve consensus through negotiation
- C. Call the supervisor
- D. Never change his/her mind
Answer: C
NEW QUESTION # 52
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Record the segment with the less aggressive profile
- C. Record your result by identifying two segments
- D. Use another method as the comparator method is too subjective
Answer: B
NEW QUESTION # 53
Daily reports are important because:
Select All That Apply
- A. the information impacts future projects.
- B. Inspectors rarely change on a project.
- C. The information aids communication with supervisors.
- D. Management uses them to make personnel decisions.
Answer: A,C,D
NEW QUESTION # 54
......
To be eligible for the NACE-CIP1-001 Exam, candidates must meet certain requirements, including a minimum of six months of experience in the coatings industry or completion of a NACE-approved training program. NACE-CIP1-001 exam is administered by NACE International, a leading organization that provides training, certification, and standards development for corrosion control professionals worldwide.
NACE-CIP1-001 [May-2025] Newly Released] NACE-CIP1-001 Exam Questions For You To Pass: https://www.passleadervce.com/CIP-Level-1/reliable-NACE-CIP1-001-exam-learning-guide.html
For your comfort, PassLeaderVCE provides you the convenience of free CIP Level 1 braindumps demo: https://drive.google.com/open?id=1YRhZ_oX9EGwlmWgKy1WuETBF0CaFTX5d