New (2022) Huawei H31-341 Exam Dumps
Best Way To Study For Huawei H31-341 Exam Brilliant H31-341 Exam Questions PDF
NEW QUESTION 43
If the tunnel APS is configured for the tunnel to which the PW belongs, the PW cannot be configured with the PW APS.
- A. FALSE
- B. TRUE
Answer: A
NEW QUESTION 44
Which of the following are the components of general package format of PWE3? (Multiple Choice)
- A. Payload
- B. MPLS label
- C. Type
- D. CW (Control Word)
Answer: A,B,D
NEW QUESTION 45
For ODUk SNCP protection, if the punch-through site is an electrical relay station, the SCP type is recommended to be configured as SC/I when configuring protection.
- A. FALSE
- B. TRUE
Answer: A
NEW QUESTION 46
The steps that must be performed when configuring the Ethernet private line service carried by the PW are as follows: (Multiple Choice)
- A. Configure the UNI port
- B. Configure MPLS tunnel
- C. Configure port DCN
- D. Configure QoS
Answer: A,B,C
NEW QUESTION 47
The setting of alarm reversal is based on:
- A. Veneer
- B. Port
- C. Network element
- D. Alarm
Answer: B
NEW QUESTION 48
Daily equipment maintenance items, excluding:
- A. Check device sound alarms
- B. Check the cabinet and board indicators
- C. Check the fan box and clean the air filter
- D. Check the room temperature, humidity and cleanliness
Answer: C
NEW QUESTION 49
When configuring the layer 2 attribute of the large network, when the "TAC ID" is set to "Access" or "Hybrid", you need to set the "default VLAN ID" and "VLAN priority" of the untagged frame.
- A. TRUE
- B. FALSE
Answer: A
NEW QUESTION 50
Which of the following description of the DM12 board are correct? (Multiple choice)
- A. One DX1 board can be used with two DM12
- B. Accessing G.703 64 kbit/s co-directional service signals through the DB44 interface on the DM12 board
- C. Electrical signal input and output interfaces for DDN, Unframed E1 and sub-rate services
- D. Access the NX6bit/s and sub-rate service signals through the DB28 connector on the DM12 board.
Answer: A,B,D
NEW QUESTION 51
Before creating an optical cross-connection, you need to manually configure the corresponding port of the corresponding board as a boundary port, for example, the line-side port of the FIU board between two sites.
- A. TRUE
- B. FALSE
Answer: A
NEW QUESTION 52
Which of the following is the incorrect description of the internal port properties of the Ethernet board?
- A. For the ingress port for the Access attribute, if the input data carries the VLAN ID, discard.
- B. For the inbound port of the Tag Aware attribute, if the input data carries the VLAN ID, transparently receive the data.
- C. For the ingress port of the Tag Aware attribute, if the input data does not carry the VLAN ID, discard.
- D. For the ingress port of the Access attribute, if the input data does not carry the VLAN ID, it is directly transparent.
Answer: D
NEW QUESTION 53
Before querying bit errors and optical power on the U2000, you need to perform the ( ) operation. Otherwise, the corresponding data cannot be queried.
- A. Creating the logical fiber
- B. Configuring data
- C. Synchronizing NE data
- D. Enabling the NE Performance Monitoring Time
Answer: B
NEW QUESTION 54
The following description of 1+1 and 1:1 optical line protection, the fault is (). (Multiple Choice)
- A. According to different placement of OLP boards in the network, 1+1 optical line protection can be divided into 1+1 OMS path protection and 1+1 OTS path protection.
- B. 1+1 optical line protection and 1:1 optical line protection use the same protection board
- C. 1:1 optical line protection switching mode can only be double-ended switching
- D. The main difference between 1:1 optical line protection and 1+1 optical line protection is whether the APS protocol is required.
Answer: B,D
NEW QUESTION 55
Which of the following are not part of the 400G originating modulation technology?
- A. FDDM/Nyquist spectrum compression technology
- B. Multi-carrier generation and multiplexing
- C. High-order modulation (xQAM)
- D. Advanced oDSP algorithm
Answer: D
NEW QUESTION 56
Which of the following signals can be used as input or output signals of an external clock interface?
- A. 2.048 MHz
- B. 155 Mbit/s
- C. 34 Mbit/s
- D. 2.048 Mbit/s
Answer: B
NEW QUESTION 57
Which of the following SOM systems is not monitored?
- A. Type of originating FEC
- B. Main light path performance
- C. Receive OTU input optical power
- D. Light performance flatness
Answer: A
NEW QUESTION 58
In the Colored&Directioned scenario of the 4D ROADM, if you want to implement local service scheduling in four directions, how many sets of M40V+D40 are needed?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION 59
The NS4 board features test includes: (Multiple choice)
- A. -20dB spectral width test
- B. Receive sensitivity
- C. Side mode suppression ratio
- D. Center wavelength test
Answer: A,B,C,D
NEW QUESTION 60
When creating an electric layer path, one RX/TX port can only establish a connection with one optical channel of the clientLP port.
- A. FALSE
- B. TRUE
Answer: A
NEW QUESTION 61
Which of the following plane technologies does the OS-OTN device incorporate? (Multiple Choice)
- A. OTN
- B. SDH
- C. PDH
- D. Grouping
Answer: A,B,D
NEW QUESTION 62
When the working channel of the optical line protection fails, it cannot be automatically switched to the protection channel. What are the possible reasons? (Multiple choice)
- A. Artificially issued a lock command
- B. Protection group parameter configuration is error
- C. Waiting for the recovery time to be set too long
- D. The protection channel is faulty
Answer: A,B,C,D
NEW QUESTION 63
Which of the following ROADM boards have WSS optical modules? (Multiple Choice)
- A. WSD9
- B. WSM9
- C. RDU9
- D. WSMD9
Answer: A,B,D
NEW QUESTION 64
......
What are the benefits of Huawei H31-341 certified professional
- The Huawei HiLTE certification will help you to get a distinct career in IT.
- Our exam product will help you to understand the questions that may come up in the actual Huawei HiLTE exam.
- Take this exam and become certified in the Huawei HiLTE.
- This certification will also help you to get an interview with top IT companies.
- Take this exam at least six months prior to the actual Huawei HiLTE exam.
- You will be given an opportunity to work with top IT companies.
Updated Verified Pass H31-341 Exam - Real Questions and Answers: https://www.passleadervce.com/HCIP-Transmission/reliable-H31-341-exam-learning-guide.html
Dumps Moneyack Guarantee - H31-341 Dumps Approved Dumps: https://drive.google.com/open?id=1bhzUcv8ckK2gzeX-MQ6x_Sg7LqC5YoVC